Complementary
Primary voltage limit	85...264 V
Network frequency	50/60 Hz
Network frequency limits	47…63 Hz
Apparent power	0.13 kVA
Input current	0.55 A 240 V; 1.01 A 115 V
Inrush current	30 A 120 V; 60 A 240 V
I²t on activation	1 A².s 120 V; 3 A².s 240 V
It on activation	0.05 A.s 120 V; 0.07 A.s 240 V
MTBF reliability	792000 H
Protection type	Internal fuse not accessible for primary circuit; Overload protection for secondary circuit; Overvoltage protection for secondary circuit; Short-circuit protection for secondary circuit
Current at secondary voltage	5.5 A 3.3 V DC I/O module logic power supply; 1.67 A 24 V DC I/O module power supply and processor
Maximum power dissipation in W	8.5 W
Status LED	1 LED (green) presence of voltages (OK); 1 LED (green) redundancy OK; 1 LED (green) power supply status
Control type	RESET push-button cold restart
Electrical connection	1 connector 2 pin(s)alarm relay; 1 connector 5 pin(s)line supply, protective earth
Insulation resistance	>= 100 MOhm primary/ground; >= 100 MOhm primary/secondary
Net weight	0.51 kg
Contractual warranty
Warranty (in months)	18
Environment
Immunity to microbreaks	1 ms
Dielectric strength	1500 V primary/secondary I/O module logic power supply; 1500 V primary/secondary I/O module power supply and processor; 2300 V primary/secondary sensor power supply; 1500 V primary/ground; 500 V 24 V sensor output/ground
Vibration resistance	3 gn
Shock resistance	30 gn
IP degree of protection	IP20
Directives	2014/35/EU - low voltage directive; 2014/30/EU - electromagnetic compatibility
Product certifications	CE; UL; CSA; RCM; EAC; Merchant Navy
Standards	IEC 61131-2; IEC 61010-2-201; UL 61010-2-201; CSA C22.2 No 61010-2-201; IACS E10; EN/IEC 61000-6-5, interface type 1 and type 2; EN/IEC 61850-3, location G
Environmental characteristic	Gas resistant class Gx conforming to ISA S71.04; Gas resistant class 3C4 conforming to IEC 60721-3-3; Dust resistant class 3S4 conforming to IEC 60721-3-3; Sand resistant class 3S4 conforming to IEC 60721-3-3; Salt resistant level 2 conforming to IEC 68252; Mold growth resistant class 3B2 conforming to IEC 60721-3-3; Fungal spore resistant class 3B2 conforming to IEC 60721-3-3; Hazardous location class I division 2
Ambient air temperature for storage	-40…85 °C
Ambient air temperature for operation	-25…70 °C
Relative humidity	5…95 % at 55 °C without condensation
Protective treatment	Conformal coating
Operating altitude	0...2000 m; 2000...5000 m with derating factor
Logistical informations
Country of origin	ID
Main
Range of product	Modicon X80
Product or component type	Power supply module
backplane compatibility	All backplane
Product specific application	For severe environments
advanced diagnostics available via network	Remaining lifetime; Temperature sensing; Redundancy test; Redundancy information; Uptime duration
Primary voltage	100...240 V
Supply circuit type	AC
Secondary power	18 W 3.3 V DC at -25…70 °C I/O module logic power supply; 40 W 24 V DC at -25…70 °C I/O module power supply and processor if 3.3 V not loaded
Packing Units
Unit Type of Package 1	PCE
Number of Units in Package 1	1
Package 1 Height	9.000 cm
Package 1 Width	18.000 cm
Package 1 Length	25.000 cm
Package 1 Weight	615.000 g
Unit Type of Package 2	S03
Number of Units in Package 2	6
Package 2 Height	30.000 cm
Package 2 Width	30.000 cm
Package 2 Length	40.000 cm
Package 2 Weight	4.480 kg

This harsh environment power supply is part of the Modicon X80 range, a range of common inputs and outputs for Modicon M340 and Modicon M580. This power supply module has a primary voltage of 100V to 240V AC for harsh environments to build redundant architectures. This robust product can be used in harsher environments and operate in an extended temperature range of -25°C to +70°C. It is equipped with a 2-pin connector for the alarm relay, a 5-pin connector for the mains supply and a protective conductor for the electrical connection. It is an IP20 certified product. This product is certified by ATEX, IEC-Ex, CE, RCM, Merchant Navy, CSA, EAC and UL. It complies with EN 61131-2, EN 61000-6-4, EN 61000-6-2 and EN 61010-2-201. A set of two removable cage terminal blocks (5-way and 2-way) is included with the power supply. The product must be installed in an X80 module carrier and secured with 2 screws.