Schneider Electric ATV320U06N4B, EAN: 3606480966392

Schneider Electric ATV320U06N4B frequency converter 380-500 V

Industrial Material > Automation > Frequency converter, soft starter

Schneider Electric ATV320U06N4B frequency converter 380-500 V

Lieske Part No. 198824
Mfg Part No ATV320U06N4B
EAN-Code 3606480966392
Manufacturer Schneider Electric
Here only 645,05 EUR
767,61 EUR incl. VAT

Further information for Schneider Electric ATV320U06N4B frequency converter 380-500 V

Complementary
Discrete input number7
Discrete input typeSTO safe torque off, 24 V DC, impedance: 1.5 kOhm; DI1...DI6 logic inputs, 24 V DC (30 V); DI5 programmable as pulse input: 0…30 kHz, 24 V DC (30 V)
Discrete input logicPositive logic (source); Negative logic (sink)
Discrete output number3
Discrete output typeOpen collector DQ+ 0…1 kHz 30 V DC 100 mA; Open collector DQ- 0…1 kHz 30 V DC 100 mA
Analogue input number3
Analogue input typeAI1 voltage: 0...10 V DC, impedance: 30 kOhm, resolution 10 bits; AI2 bipolar differential voltage: +/- 10 V DC, impedance: 30 kOhm, resolution 10 bits; AI3 current: 0...20 mA (or 4-20 mA, x-20 mA, 20-x mA or other patterns by configuration), impedance: 250 Ohm, resolution 10 bits
Analogue output number1
Analogue output typeSoftware-configurable current AQ1: 0...20 mA impedance 800 Ohm, resolution 10 bits; Software-configurable voltage AQ1: 0...10 V DC impedance 470 Ohm, resolution 10 bits
Relay output typeConfigurable relay logic R1A 1 NO electrical durability 100000 cycles; Configurable relay logic R1B 1 NC electrical durability 100000 cycles; Configurable relay logic R1C; Configurable relay logic R2A 1 NO electrical durability 100000 cycles; Configurable relay logic R2C
Maximum switching currentRelay output R1A, R1B, R1C on resistive load, cos phi = 1: 3 A at 250 V AC; Relay output R1A, R1B, R1C on resistive load, cos phi = 1: 3 A at 30 V DC; Relay output R1A, R1B, R1C, R2A, R2C on inductive load, cos phi = 0.4 and L/R = 7 ms: 2 A at 250 V AC; Relay output R1A, R1B, R1C, R2A, R2C on inductive load, cos phi = 0.4 and L/R = 7 ms: 2 A at 30 V DC; Relay output R2A, R2C on resistive load, cos phi = 1: 5 A at 250 V AC; Relay output R2A, R2C on resistive load, cos phi = 1: 5 A at 30 V DC
Minimum switching currentRelay output R1A, R1B, R1C, R2A, R2C: 5 mA at 24 V DC
Method of accessSlave CANopen
4 quadrant operation possibleTrue
Asynchronous motor control profileVoltage/frequency ratio, 5 points; Flux vector control without sensor, standard; Voltage/frequency ratio - Energy Saving, quadratic U/f; Flux vector control without sensor - Energy Saving; Voltage/frequency ratio, 2 points
Synchronous motor control profileVector control without sensor
Maximum output frequency0.599 kHz
Acceleration and deceleration rampsLinear; U; S; CUS; Ramp switching; Acceleration/deceleration ramp adaptation; Acceleration/deceleration automatic stop with DC injection
Motor slip compensationAutomatic whatever the load; Adjustable 0...300 %; Not available in voltage/frequency ratio (2 or 5 points)
Switching frequency2...16 kHz adjustable; 4...16 kHz with derating factor
Nominal switching frequency4 kHz
Braking to standstillBy DC injection
Brake chopper integratedTrue
Line current2.8 A at 380 V (heavy duty); 2.2 A at 500 V (heavy duty)
Maximum input current2.8 A
Maximum output voltage500 V
Apparent power1.9 kVA at 500 V (heavy duty)
Network frequency50...60 Hz
Relative symmetric network frequency tolerance5 %
Prospective line Isc5 kA
Base load current at high overload4.1 A
Power dissipation in WFan: 27.0 W at 380 V, switching frequency 4 kHz
With safety function Safely Limited Speed (SLS)True
With safety function Safe brake management (SBC/SBT)False
With safety function Safe Operating Stop (SOS)False
With safety function Safe Position (SP)False
With safety function Safe programmable logicFalse
With safety function Safe Speed Monitor (SSM)False
With safety function Safe Stop 1 (SS1)True
With sft fct Safe Stop 2 (SS2)False
With safety function Safe torque off (STO)True
With safety function Safely Limited Position (SLP)False
With safety function Safe Direction (SDI)False
Protection typeInput phase breaks: drive; Overcurrent between output phases and earth: drive; Overheating protection: drive; Short-circuit between motor phases: drive; Thermal protection: drive
Width45.0 mm
Height325.0 mm
Depth245.0 mm
Net weight2.5 kg
Transient overtorque170…200 % of nominal motor torque
Contractual warranty
Warranty (in months)18
Environment
Operating positionVertical +/- 10 degree
Product certificationsCE; ATEX; NOM; GOST; EAC; RCM; KC
MarkingCE; ATEX; UL; CSA; EAC; RCM
StandardsIEC 61800-5-1
Electromagnetic compatibilityElectrostatic discharge immunity test level 3 conforming to IEC 61000-4-2; Radiated radio-frequency electromagnetic field immunity test level 3 conforming to IEC 61000-4-3; Electrical fast transient/burst immunity test level 4 conforming to IEC 61000-4-4; 1.2/50 µs - 8/20 µs surge immunity test level 3 conforming to IEC 61000-4-5; Conducted radio-frequency immunity test level 3 conforming to IEC 61000-4-6; Voltage dips and interruptions immunity test conforming to IEC 61000-4-11
Environmental class (during operation)Class 3C3 according to IEC 60721-3-3; Class 3S2 according to IEC 60721-3-3
Maximum acceleration under shock impact (during operation)150 m/s² at 11 ms
Maximum acceleration under vibrational stress (during operation)10 m/s² at 13...200 Hz
Maximum deflection under vibratory load (during operation)1.5 mm at 2...13 Hz
Permitted relative humidity (during operation)Class 3K5 according to EN 60721-3
Volume of cooling air9.4 m3/h
Overvoltage categoryIII
Regulation loopAdjustable PID regulator
Speed accuracy+/- 10 % of nominal slip 0.2 Tn to Tn
Pollution degree2
Ambient air transport temperature-25…70 °C
Ambient air temperature for operation-10…50 °C without derating; 50…60 °C with derating factor
Ambient air temperature for storage-25…70 °C
Logistical informations
Country of originID
Main
Range of productAltivar Machine ATV320
Product or component typeVariable speed drive
Product specific applicationComplex machines
VariantStandard version
Format of the driveBook
Mounting modeCabinet mount
Communication port protocolModbus serial; CANopen
Option cardCommunication module, CANopen; Communication module, EtherCAT; Communication module, Profibus DP V1; Communication module, PROFINET; Communication module, Ethernet Powerlink; Communication module, EtherNet/IP; Communication module, DeviceNet
[Us] rated supply voltage380...500 V - 15...10 %
nominal output current1.9 A
Motor power kW0.55 kW for heavy duty
Motor power hp0.75 hp
EMC filterClass C2 EMC filter integrated
IP degree of protectionIP20
Packing Units
Unit Type of Package 1PCE
Number of Units in Package 11
Package 1 Height8.500 cm
Package 1 Width27.500 cm
Package 1 Length32.500 cm
Package 1 Weight2.335 kg
Unit Type of Package 2S06
Number of Units in Package 224
Package 2 Height75.000 cm
Package 2 Width60.000 cm
Package 2 Length80.000 cm
Package 2 Weight75.256 kg
The frequency converter ATV320U06N4B from Schneider Electric belongs to the Altivar Machine ATV320 series and is designed as a variable speed drive for use in complex machines. It is book-sized and intended for mounting in an enclosure. The operating voltage is 380 to 500 V, 3-phase, with a tolerance of -15 % to +10 %. The converter features an integrated EMC filter of class C2, which can be optionally deactivated, and is suitable for operation on IT networks. The rated output power is 0.55 kW under heavy-duty operation, equivalent to a motor power of 0.75 hp. The maximum output frequency is 599 Hz, enabling high-speed control.

Applications

The frequency converter is designed for industrial applications involving complex machines, particularly in systems requiring precise speed control and high operational safety. It is suitable for operating asynchronous and synchronous motors in open-loop mode, where vector-oriented flux control without a sensor (SVC) ensures high speed quality and stability. The integrated safety technology includes five functions: safe torque off (STO), safe hold 1 (SS1), safe limited speed (SLS), safe guard door interlock (GDL), and safe maximum speed (SMS). These functions are relevant for use in safety-critical applications.

Functions and Equipment in Detail

The converter features 7 discrete inputs, including an STO safety input (24 V DC, impedance 1.5 kOhm) and six logic inputs (24 V DC, 30 V), with DI5 programmable as a pulse input (0–30 kHz). The discrete outputs include three open-collector outputs (0–1 kHz, 30 V DC, 100 mA). There are three analog inputs: AI1 (0–10 V DC, 30 kOhm, 10 bit), AI2 (bipolar differential voltage ±10 V DC, 30 kOhm, 10 bit), and AI3 (0–20 mA, 250 Ohm, 10 bit). An analog output AQ1 is software-configurable for current (0–20 mA, 800 Ohm) or voltage (0–10 V DC, 470 Ohm), each with 10-bit resolution. Additionally, configurable relay outputs are available, including R1A, R1B, R1C, R2A, and R2C, with an electrical life of 100,000 cycles. The maximum currents are 3 A (ohmic, 250 V AC/30 V DC) and 2 A (inductive, 250 V AC/30 V DC) for R1A–R1C, and 5 A (ohmic, 250 V AC/30 V DC) for R2A and R2C. The minimum switching current is 5 mA at 24 V DC.

Technology Explained Simply

Control is performed via various profiles: U/f characteristic (2- and 5-point), vector-oriented flux control without sensor (standard and energy-saving mode), U/f characteristic in energy-saving mode, and quadratic U/f characteristic. For synchronous motors, vector-oriented flux control without encoder is available. Acceleration and deceleration ramps can be linear, U-shaped, S-shaped, CUS-shaped, or configured via ramp switching. Automatic ramp adaptation and automatic stop with DC injection are also possible. Motor slip compensation is automatic and independent of load, adjustable from 0 to 300 %, but not available with U/f characteristics. The integrated braking module enables 4-quadrant operation without additional components.

Compatibility and Accessories

The frequency converter supports various communication protocols: Modbus serial and CANopen. Optional communication modules for EtherCAT, Profibus DP V1, Profinet, Ethernet Powerlink, EtherNet/IP, and DeviceNet can be added. Suitable accessories include line reactors (e.g. VW3-A4551), power contactors (e.g. LC1D09BL, LC1D09FE7), braking resistors (e.g. VW3A7730), motor protection switches (e.g. GV2L08), and various option cards such as VW3-A3607 (Profibus DPv1), VW3A3627 (Profinet), VW3A3609 (DeviceNet), VW3A3608 (CANopen Daisy Chain), and VW3A3616 (Ethernet TCP/IP). Configuration can be done via the commissioning software SoMove, decentralized terminals, or configuration tools such as Simple-Loader and Multi-Loader.

Mounting and Installation

The converter is book-sized and intended for mounting in an enclosure. Dimensions are 45 mm (width) × 325 mm (height) × 245 mm (depth). It is delivered with an EMC plate for customer-side mounting. The protection rating is IP20, providing protection against touch and entry of solid foreign objects larger than 12.5 mm. Commissioning is done via Plug & Drive, with the converter pre-configured for common applications. Configuration can be adjusted, saved, or loaded at any time using the mentioned tools.

Advantages in Operation

The frequency converter offers easy commissioning, intuitive operation, and high operational safety due to integrated safety functions. Vector-oriented control enables precise speed control, even under variable loads. The integrated inputs and outputs, along with communication capability via various protocols, allow flexible integration into existing control systems. The integrated braking module reduces the need for additional components. The EMC filtering of class C2 ensures low electromagnetic emission, and the filter can be optionally deactivated if required for the application.

Protection Rating IP20

The IP20 protection rating means the converter is protected against touch with fingers or similar objects and against entry of solid foreign objects larger than 12.5 mm. It is not suitable for outdoor use or in damp environments, as it is neither dust-tight nor waterproof. Mounting is exclusively in an enclosure.

Communication Protocols

Integrated communication is via Modbus serial and CANopen. Additional communication modules enable connection to EtherCAT, Profibus DP V1, Profinet, Ethernet Powerlink, EtherNet/IP, and DeviceNet. These extensions are optionally available and allow flexible integration into various automation environments.

4-Quadrant Operation

4-quadrant operation is possible, with the integrated braking module enabling necessary energy dissipation. This is particularly relevant for applications where the motor can return energy during forward, reverse, and braking operations.

EMC Filter Class C2

The integrated EMC filter of class C2 reduces electromagnetic emission and is suitable for operation on IT networks. The filter can be switched off if required for the application. Filtering is performed via an integrated EMC plate intended for customer-side mounting.

Control Profiles

Control profiles include U/f characteristics (2- and 5-point), vector-oriented flux control without sensor (standard and energy-saving mode), U/f characteristic in energy-saving mode, and quadratic U/f characteristic. For synchronous motors, vector-oriented flux control without encoder is available. Profile selection depends on requirements for speed accuracy, energy efficiency, and load behavior.

Ramp Control

Acceleration and deceleration ramps can be linear, U-shaped, S-shaped, CUS-shaped, or configured via ramp switching. Automatic ramp adaptation and automatic stop with DC injection are also possible. Ramp control influences the motor’s acceleration and braking behavior and is crucial for operational safety and system lifespan.

Motor Protection

Motor slip compensation is automatic and independent of load, adjustable from 0 to 300 %. This function is not available with U/f characteristics. Slip compensation ensures the motor maintains constant speed even under load fluctuations.

Access Method

Access is via the slave function in the CANopen protocol. This enables decentralized control and integration into CANopen-based systems.

Commissioning and Configuration

Commissioning is done via Plug & Drive, with the converter pre-configured for common applications. Configuration can be adjusted, saved, or loaded at any time using the commissioning software SoMove, decentralized terminals, or configuration tools such as Simple-Loader and Multi-Loader. This enables flexible adaptation to specific requirements and easy maintenance.

Accessories

Suitable accessories include line reactors (e.g. VW3-A4551), power contactors (e.g. LC1D09BL, LC1D09FE7), braking resistors (e.g. VW3A7730), motor protection switches (e.g. GV2L08), and various option cards such as VW3-A3607 (Profibus DPv1), VW3A3627 (Profinet), VW3A3609 (DeviceNet), VW3A3608 (CANopen Daisy Chain), and VW3A3616 (Ethernet TCP/IP). These components extend the functionality and integration options of the converter.

Dimensions and Mounting

Dimensions are 45 mm (width) × 325 mm (height) × 245 mm (depth). The converter is book-sized and intended for mounting in an enclosure. It is delivered with an EMC plate for customer-side mounting. The protection rating is IP20, providing protection against touch and entry of solid foreign objects larger than 12.5 mm. Mounting is exclusively in an enclosure.

Safety Functions

The integrated safety technology includes five functions: safe torque off (STO), safe hold 1 (SS1), safe limited speed (SLS), safe guard door interlock (GDL), and safe maximum speed (SMS). These functions are relevant for use in safety-critical applications and enable safe control of the drive.

Operating Voltage and Power

The operating voltage is 380 to 500 V, 3-phase, with a tolerance of -15 % to +10 %. The rated output power is 0.55 kW under heavy-duty operation, equivalent to a motor power of 0.75 hp. The maximum output frequency is 599 Hz, enabling high-speed control.

Communication and Integration

Communication is via Modbus serial and CANopen. Additional communication modules enable connection to EtherCAT, Profibus DP V1, Profinet, Ethernet Powerlink, EtherNet/IP, and DeviceNet. These extensions are optionally available and allow flexible integration into various automation environments.

Configuration Tools

Configuration can be done via the commissioning software SoMove, decentralized terminals, or configuration tools such as Simple-Loader and Multi-Loader. This enables flexible adaptation to specific requirements and easy maintenance.

Accessories and Extensions

Suitable accessories include line reactors (e.g. VW3-A4551), power contactors (e.g. LC1D09BL, LC1D09FE7), braking resistors (e.g. VW3A7730), motor protection switches (e.g. GV2L08), and various option cards such as VW3-A3607 (Profibus DPv1), VW3A3627 (Profinet), VW3A3609 (DeviceNet), VW3A3608 (CANopen Daisy Chain), and VW3A3616 (Ethernet TCP/IP). These components extend the functionality and integration options of the converter.

Commissioning and Maintenance

Commissioning is done via Plug & Drive, with the converter pre-configured for common applications. Configuration can be adjusted, saved, or loaded at any time using the commissioning software SoMove, decentralized terminals, or configuration tools such as Simple-Loader and Multi-Loader. This enables flexible adaptation to specific requirements and easy maintenance.

Frequency Converter
Altivar Machine ATV320
EMC Filter Class C2
IP20
4-Quadrant Operation
SVC Control
Modbus, CANopen
This is an offer of:

Lieske Elektronik e.K.

Reutener Str. 10
79279 Vörstetten

https://industry-electronics.com
Tel. 07666/88499-0
Fax. 07666/88499-111

Diesen Artikel finden Sie unter:
industry-electronics.com/artikel/198824
qrcode für Schneider Electric ATV320U06N4B frequency converter 380-500 V