| Complementary |
| Discrete input number | 7 |
| Discrete input type | STO safe torque off, 24 V DC, impedance: 1.5 kOhm; DI1...DI6 logic inputs, 24 V DC (30 V); DI5 programmable as pulse input: 0…30 kHz, 24 V DC (30 V) |
| Discrete input logic | Positive logic (source); Negative logic (sink) |
| Discrete output number | 3 |
| Discrete output type | Open collector DQ+ 0…1 kHz 30 V DC 100 mA; Open collector DQ- 0…1 kHz 30 V DC 100 mA |
| Analogue input number | 3 |
| Analogue input type | AI1 voltage: 0...10 V DC, impedance: 30 kOhm, resolution 10 bits; AI2 bipolar differential voltage: +/- 10 V DC, impedance: 30 kOhm, resolution 10 bits; AI3 current: 0...20 mA (or 4-20 mA, x-20 mA, 20-x mA or other patterns by configuration), impedance: 250 Ohm, resolution 10 bits |
| Analogue output number | 1 |
| Analogue output type | Software-configurable current AQ1: 0...20 mA impedance 800 Ohm, resolution 10 bits; Software-configurable voltage AQ1: 0...10 V DC impedance 470 Ohm, resolution 10 bits |
| Relay output type | Configurable relay logic R1A 1 NO electrical durability 100000 cycles; Configurable relay logic R1B 1 NC electrical durability 100000 cycles; Configurable relay logic R1C; Configurable relay logic R2A 1 NO electrical durability 100000 cycles; Configurable relay logic R2C |
| Maximum switching current | Relay output R1A, R1B, R1C on resistive load, cos phi = 1: 3 A at 250 V AC; Relay output R1A, R1B, R1C on resistive load, cos phi = 1: 3 A at 30 V DC; Relay output R1A, R1B, R1C, R2A, R2C on inductive load, cos phi = 0.4 and L/R = 7 ms: 2 A at 250 V AC; Relay output R1A, R1B, R1C, R2A, R2C on inductive load, cos phi = 0.4 and L/R = 7 ms: 2 A at 30 V DC; Relay output R2A, R2C on resistive load, cos phi = 1: 5 A at 250 V AC; Relay output R2A, R2C on resistive load, cos phi = 1: 5 A at 30 V DC |
| Minimum switching current | Relay output R1A, R1B, R1C, R2A, R2C: 5 mA at 24 V DC |
| Method of access | Slave CANopen |
| 4 quadrant operation possible | True |
| Asynchronous motor control profile | Voltage/frequency ratio, 5 points; Flux vector control without sensor, standard; Voltage/frequency ratio - Energy Saving, quadratic U/f; Flux vector control without sensor - Energy Saving; Voltage/frequency ratio, 2 points |
| Synchronous motor control profile | Vector control without sensor |
| Maximum output frequency | 0.599 kHz |
| Acceleration and deceleration ramps | Linear; U; S; CUS; Ramp switching; Acceleration/deceleration ramp adaptation; Acceleration/deceleration automatic stop with DC injection |
| Motor slip compensation | Automatic whatever the load; Adjustable 0...300 %; Not available in voltage/frequency ratio (2 or 5 points) |
| Switching frequency | 2...16 kHz adjustable; 4...16 kHz with derating factor |
| Nominal switching frequency | 4 kHz |
| Braking to standstill | By DC injection |
| Brake chopper integrated | True |
| Line current | 5.9 A at 200 V (heavy duty); 4.9 A at 240 V (heavy duty) |
| Maximum input current | 5.9 A |
| Maximum output voltage | 240 V |
| Apparent power | 1.2 kVA at 240 V (heavy duty) |
| Network frequency | 50...60 Hz |
| Relative symmetric network frequency tolerance | 5 % |
| Prospective line Isc | 1 kA |
| Base load current at high overload | 3.7 A |
| Power dissipation in W | Self-cooled: 30 W at 200 V, switching frequency 4 kHz |
| With safety function Safely Limited Speed (SLS) | True |
| With safety function Safe brake management (SBC/SBT) | False |
| With safety function Safe Operating Stop (SOS) | False |
| With safety function Safe Position (SP) | False |
| With safety function Safe programmable logic | False |
| With safety function Safe Speed Monitor (SSM) | False |
| With safety function Safe Stop 1 (SS1) | True |
| With sft fct Safe Stop 2 (SS2) | False |
| With safety function Safe torque off (STO) | True |
| With safety function Safely Limited Position (SLP) | False |
| With safety function Safe Direction (SDI) | False |
| Protection type | Input phase breaks: drive; Overcurrent between output phases and earth: drive; Overheating protection: drive; Short-circuit between motor phases: drive; Thermal protection: drive |
| Width | 72.0 mm |
| Height | 143.0 mm |
| Depth | 128.0 mm |
| Net weight | 1 kg |
| Transient overtorque | 170…200 % of nominal motor torque |
| Contractual warranty |
| Warranty (in months) | 18 |
| Environment |
| Operating position | Vertical +/- 10 degree |
| Product certifications | CE; ATEX; NOM; GOST; EAC; RCM; KC |
| Marking | CE; ATEX; UL; CSA; EAC; RCM |
| Standards | IEC 61800-5-1 |
| Electromagnetic compatibility | Electrostatic discharge immunity test level 3 conforming to IEC 61000-4-2; Radiated radio-frequency electromagnetic field immunity test level 3 conforming to IEC 61000-4-3; Electrical fast transient/burst immunity test level 4 conforming to IEC 61000-4-4; 1.2/50 µs - 8/20 µs surge immunity test level 3 conforming to IEC 61000-4-5; Conducted radio-frequency immunity test level 3 conforming to IEC 61000-4-6; Voltage dips and interruptions immunity test conforming to IEC 61000-4-11 |
| Environmental class (during operation) | Class 3C3 according to IEC 60721-3-3; Class 3S2 according to IEC 60721-3-3 |
| Maximum acceleration under shock impact (during operation) | 150 m/s² at 11 ms |
| Maximum acceleration under vibrational stress (during operation) | 10 m/s² at 13...200 Hz |
| Maximum deflection under vibratory load (during operation) | 1.5 mm at 2...13 Hz |
| Permitted relative humidity (during operation) | Class 3K5 according to EN 60721-3 |
| Overvoltage category | III |
| Regulation loop | Adjustable PID regulator |
| Speed accuracy | +/- 10 % of nominal slip 0.2 Tn to Tn |
| Pollution degree | 2 |
| Ambient air transport temperature | -25…70 °C |
| Ambient air temperature for operation | -10…50 °C without derating; 50…60 °C with derating factor |
| Ambient air temperature for storage | -25…70 °C |
| Logistical informations |
| Country of origin | ID |
| Main |
| Range of product | Altivar Machine ATV320 |
| Product or component type | Variable speed drive |
| Product specific application | Complex machines |
| Variant | Standard version |
| Format of the drive | Compact |
| Mounting mode | Wall mount |
| Communication port protocol | Modbus serial; CANopen |
| Option card | Communication module, CANopen; Communication module, EtherCAT; Communication module, Profibus DP V1; Communication module, PROFINET; Communication module, Ethernet Powerlink; Communication module, EtherNet/IP; Communication module, DeviceNet |
| [Us] rated supply voltage | 200...240 V - 15...10 % |
| nominal output current | 3.3 A |
| Motor power kW | 0.37 kW for heavy duty |
| Motor power hp | 0.5 hp |
| EMC filter | Class C2 EMC filter integrated |
| IP degree of protection | IP20 |
| Packing Units |
| Unit Type of Package 1 | PCE |
| Number of Units in Package 1 | 1 |
| Package 1 Height | 11.500 cm |
| Package 1 Width | 18.500 cm |
| Package 1 Length | 19.500 cm |
| Package 1 Weight | 1.206 kg |
| Unit Type of Package 2 | S06 |
| Number of Units in Package 2 | 45 |
| Package 2 Height | 75.000 cm |
| Package 2 Width | 60.000 cm |
| Package 2 Length | 80.000 cm |
| Package 2 Weight | 66.145 kg |
The ATV320U04M2C frequency converter from Schneider Electric is a compact variable-speed drive from the Altivar Machine ATV320 series, specifically designed for use in complex machines. It is suitable for applications requiring precise speed control and flexible operating conditions, particularly in industrial environments with single-phase supply voltage of 200 to 240 V at 50/60 Hz. The converter features a rated output power of 0.37 kW (0.5 hp) and is designed for heavy-duty operation. It is delivered in a compact format enabling surface mounting and is equipped with an integrated EMC filter of class C2, which is deactivatable and supports operation on IT networks.
Applications
The ATV320U04M2C is designed for use in complex machines and systems where flexible and precise motor control is required. It is particularly suitable for applications in automation technology, where variable speed, high operational reliability, and integrated safety functions are required. The integrated safety technology includes five functions: safe torque off (STO), safe stop 1 (SS1), safe limited speed (SLS), safe guard door interlock (GDL), and safe maximum speed (SMS). These functions enable safe operation in accordance with the requirements of the Machinery Directive.
Functions and Equipment in Detail
The converter offers a variety of input and output interfaces. It features 7 discrete inputs, including an STO safety input (24 V DC, impedance 1.5 kOhm) and six logic inputs (24 V DC, 30 V), where DI5 is programmable as a pulse input (0…30 kHz). The discrete outputs include three open-collector outputs (0…1 kHz, 30 V DC, 100 mA). Additionally, there are three analog inputs: AI1 (0–10 V DC, 30 kOhm, 10 bit), AI2 (±10 V DC, 30 kOhm, 10 bit), and AI3 (0–20 mA, 250 Ohm, 10 bit), where AI3 is configurable. An analog output AQ1 is software-configurable as current (0–20 mA, 800 Ohm) or voltage (0–10 V DC, 470 Ohm), each with 10-bit resolution. The relay outputs are configurable and offer an electrical life of 100,000 cycles; the maximum currents are 3 A (ohmic, 250 V AC) or 5 A (ohmic, 250 V AC) for R2A/R2C.
Technology Explained Simply
The ATV320U04M2C supports various control profiles, including U/f characteristics (2- and 5-point), sensorless vector control (SVC), and energy-saving modes. The SVC control enables high speed quality and stability without an encoder. Four-quadrant operation is enabled by an integrated braking module, eliminating the need for additional components. The maximum output frequency is 599 Hz. Acceleration and deceleration ramps are adjustable in linear, U-, S-, or CUS-shape, with automatic ramp adaptation and automatic stop with DC brake also possible. Motor slip compensation is automatic and adjustable independently of load (0–300 %), but not available with U/f characteristics with 2 or 5 points.
Compatibility and Accessories
The converter is designed for operation with asynchronous and synchronous motors in open-loop mode. It supports various communication protocols, including Modbus serial and CANopen. For extended connectivity options, various option cards are available, such as CANopen, EtherCAT, Profibus DP V1, Profinet, Ethernet Powerlink, EtherNet/IP, and DeviceNet. Suitable accessories include contactors (e.g. LC1D09BL, LC1D09FE7), braking resistors (e.g. VW3A7730), communication cards (e.g. VW3A3607, VW3A3627), mechanical adapters (e.g. VW3A3600), and DIN rail adapters (e.g. VW3A9804). Configuration can be performed using tools such as the commissioning software SoMove, decentralized terminals, or configuration tools like Simple-Loader and Multi-Loader.
Mounting and Installation
The converter is designed for surface mounting and is delivered with an EMC plate for customer-side mounting. Dimensions are 72 mm (width) × 143 mm (height) × 128 mm (depth). The protection rating is IP20, making it suitable for use in indoor environments. The integrated safety technology and Plug-&-Drive function simplify commissioning and enable pre-configured settings for common applications.
Operational Advantages
The ATV320U04M2C offers high operational reliability through integrated safety functions, flexible control via diverse input and output interfaces, and easy commissioning. The integrated EMC technology and braking module reduce the need for additional components. Support for various communication protocols enables flexible integration into existing automation systems. Configuration options via various tools increase efficiency during commissioning and maintenance.
Protection Rating (IP)
The IP20 protection rating ensures protection against finger contact and against solid foreign objects larger than 12.5 mm, but not against splashing water or dust. The converter is therefore intended for use in dry indoor environments.
Communication Protocols
Integrated communication is via Modbus serial and CANopen. Additional communication modules enable connection to EtherCAT, Profibus DP V1, Profinet, Ethernet Powerlink, EtherNet/IP, and DeviceNet, allowing flexible integration into various automation environments.
EMC Filter
The integrated EMC filter of class C2 is deactivatable and supports operation on IT networks. It reduces electromagnetic interference and ensures compatible network operation.
4-Quadrant Operation
Four-quadrant operation is enabled by an integrated braking module, eliminating the need for additional components. This allows both drive and braking phases of the motor in both directions of rotation.
Control Profiles
Control profiles include U/f characteristics (2- and 5-point), sensorless vector control (SVC), and energy-saving modes. SVC control offers high speed quality and stability without an encoder. U/f characteristics are suitable for simple applications, while vector control enables more precise control.
Analog Interfaces
The three analog inputs (AI1: 0–10 V DC, AI2: ±10 V DC, AI3: 0–20 mA) and the configurable analog output (AQ1: 0–20 mA or 0–10 V DC) enable flexible connection to sensors and control devices. Resolution is 10 bits for all analog interfaces.
Discrete Interfaces
The seven discrete inputs (including STO) and three discrete outputs (open collector) offer flexible control options. The inputs are programmable, with DI5 configurable as a pulse input (0–30 kHz). The outputs are rated for frequencies up to 1 kHz.
Relay Outputs
The relay outputs are configurable and offer an electrical life of 100,000 cycles. Maximum currents are 3 A (ohmic, 250 V AC) for R1A/R1B/R1C and 5 A (ohmic, 250 V AC) for R2A/R2C.
Commissioning and Configuration
Commissioning is performed using Plug-&-Drive functions, with the converter pre-configured. Configuration can be done via the commissioning software SoMove, decentralized terminals, or configuration tools such as Simple-Loader and Multi-Loader. Configurations can be loaded, edited, and secured.
Safety Functions
The integrated safety technology includes five functions: safe torque off (STO), safe stop 1 (SS1), safe limited speed (SLS), safe guard door interlock (GDL), and safe maximum speed (SMS). These functions enable safe operation in accordance with the requirements of the Machinery Directive.
Maximum Output Frequency
The maximum output frequency is 599 Hz, enabling high-speed control.
Acceleration and Deceleration Ramps
Ramps are adjustable in linear, U-, S-, or CUS-shape. Automatic ramp adaptation and automatic stop with DC brake are also possible.
Motor Protection
Motor slip compensation is automatic and adjustable independently of load (0–300 %), but not available with U/f characteristics with 2 or 5 points.
Communication Modules
Additional communication modules enable connection to EtherCAT, Profibus DP V1, Profinet, Ethernet Powerlink, EtherNet/IP, and DeviceNet, allowing flexible integration into various automation environments.
Accessories
Suitable accessories include contactors (e.g. LC1D09BL, LC1D09FE7), braking resistors (e.g. VW3A7730), communication cards (e.g. VW3A3607, VW3A3627), mechanical adapters (e.g. VW3A3600), and DIN rail adapters (e.g. VW3A9804). These components support integration and operation of the converter in various application scenarios.
Mounting
The converter is designed for surface mounting and is delivered with an EMC plate for customer-side mounting. Dimensions are 72 mm (width) × 143 mm (height) × 128 mm (depth). The protection rating is IP20, making it suitable for use in indoor environments.
Operation
Operation is with single-phase supply voltage of 200 to 240 V at 50/60 Hz. The rated output power is 0.37 kW (0.5 hp). The integrated EMC filter of class C2 is deactivatable and supports operation on IT networks.
Safety
The integrated safety technology includes five functions: safe torque off (STO), safe stop 1 (SS1), safe limited speed (SLS), safe guard door interlock (GDL), and safe maximum speed (SMS). These functions enable safe operation in accordance with the requirements of the Machinery Directive.
Configuration
Configuration is performed via the commissioning software SoMove, decentralized terminals, or configuration tools such as Simple-Loader and Multi-Loader. Configurations can be loaded, edited, and secured.
Frequency Converter
Altivar Machine ATV320
variable speed
IP20
EMC filter class C2
4-quadrant operation
STO safety