| Complementary |
| Assembly style | With heat sink |
| Function available | Integrated bypass |
| Supply voltage limits | 180…528 V |
| Supply frequency | 50...60 Hz - 5...5 % |
| Network frequency | 47.5...63 Hz |
| [Uc] Control circuit voltage | 24 V DC +/- 10 % |
| Starting time | 1 s / 100; 5 s / 20; 10 s / 10; Adjustable from 1 to 10 s |
| Deceleration time symb | Adjustable from 1 to 10 s |
| Starting torque | 30...80 % of starting torque of motor connected directly on the line supply |
| Discrete input type | Logic (LI1, LI2, BOOST) stop, run and boost on start-up functions |
| Discrete input voltage | 24...40 V |
| Input output isolation | Galvanic between power and control |
| Discrete input logic | Positive LI1, LI2, BOOST at State 0: < 5 V and 13 V, >= 0.5 mA |
| Discrete output current | 2 A DC-13; 3 A AC-15 |
| Discrete output type | Open collector logic LO1 end of starting signal; Relay outputs R1A, R1C NO |
| Discrete output voltage | 24 V (voltage limits: 6...30 V) open collector logic |
| Minimum switching current | 10 mA at 6 V DC for relay outputs |
| Maximum switching current | Relay outputs: 2 A at 30 V DC cos phi = 0.5 and L/R = 20 ms inductive load; Relay outputs: 2 A at 250 V AC AC-15 cos phi = 0.5 and L/R = 20 ms inductive load |
| Maximum switching voltage | 440 V relay outputs |
| Display type | 1 LED (green) for starter powered up; 1 LED (yellow) for nominal voltage reached |
| Tightening torque | 1.9…2.5 N.m; 0.5 N.m |
| Marking | CE |
| Operating position | Vertical +/- 10 degree |
| Height | 234 mm |
| Width | 45 mm |
| Depth | 150 mm |
| Net weight | 0.34 kg |
| Power range | 2.2…3 kW at 200…240 V 3 phases; 4…6 kW at 380…440 V 3 phases |
| Motor starter type | Soft starter |
| Contractual warranty |
| Warranty (in months) | 18 |
| Environment |
| Standards | EN/IEC 60947-4-2 |
| Product certifications | UL; CCC; C-Tick; CSA |
| IP degree of protection | IP20 |
| Pollution degree | 2 conforming to EN/IEC 60947-4-2 |
| Vibration resistance | 1 gn (f= 13…150 Hz) conforming to EN/IEC 60068-2-6; 1.5 mm peak to peak (f= 3…13 Hz) conforming to EN/IEC 60068-2-6 |
| Shock resistance | 15 gn for 11 ms conforming to EN/IEC 60068-2-27 |
| Relative humidity | 5…95 % without condensation or dripping water conforming to EN/IEC 60068-2-3 |
| Ambient air temperature for operation | -10…40 °C (without derating); 40…50 °C (with current derating of 2 % per °C) |
| Ambient air temperature for storage | -25…70 °C conforming to EN/IEC 60947-4-2 |
| Operating altitude | 1000 m with current derating of 2.2 % per additional 100 m |
| Logistical informations |
| Country of origin | DE |
| Main |
| Range of product | Altistart U01 and TeSys U |
| Product destination | Asynchronous motors |
| Product or component type | Soft starter |
| Product specific application | Simple machine |
| Device short name | ATSU01 |
| Network number of phases | 3 phases |
| [Us] rated supply voltage | 200...480 V - 10...10 % |
| Motor power kW | 2.2 kW, 3 phases at 230 V; 5.5 kW, 3 phases at 400 V; 3 kW, 3 phases at 230 V |
| Motor power hp | 3 hp, 3 phases at 230 V; 7.5 hp, 3 phases at 460 V |
| IcL starter rating | 12 A |
| Utilisation category | AC-53B conforming to EN/IEC 60947-4-2 |
| Current consumption | 65 mA |
| Type of start | Start with voltage ramp |
| Power dissipation in W | 1.5 W at full load and at end of starting; 121.5 W in transient state |
| Packing Units |
| Unit Type of Package 1 | PCE |
| Number of Units in Package 1 | 1 |
| Package 1 Height | 5.5 cm |
| Package 1 Width | 17.5 cm |
| Package 1 Length | 15.0 cm |
| Package 1 Weight | 453.0 g |
| Unit Type of Package 2 | S03 |
| Number of Units in Package 2 | 14 |
| Package 2 Height | 30 cm |
| Package 2 Width | 30 cm |
| Package 2 Length | 40 cm |
| Package 2 Weight | 6.889 kg |
The Altistart U01 is a soft start/soft stop device for 3-phase asynchronous motors. It is primarily intended to be combined with TeSys U-Starter controllers. It can be used for a motor with a rated power of up to 3 kW or 7.5 HP for 3 phases (200 V to 480 V AC) and up to 12 A. With a width of 45 mm, it is one of the smallest soft starters on the market. It can be installed almost anywhere. It has an integrated bypass that reduces noise and heat dissipation. The protection class is IP20. It weighs 0.34 kg and has the following dimensions: 45 mm wide, 234 mm high, 150 mm deep. The Altistart U01 is designed for the following simple applications: conveyor belts, pumps, fans, compressors, automatic doors and gates, small cranes and belt-driven machines. It complies with the IEC/EN 60947-4-2 standards and carries the UL, CSA, C-Tick and CCC certifications and the CE marking. It can be easily combined with a TeSys U controller using the VW3G4104 power connector. It is easy to install on a DIN rail. Altistart 01 combines simplicity with easy wiring, quick configuration and efficiency. Reduced machine wear and minimized maintenance times optimize operations. Together with the TeSys Model U, it offers a unique motor starter solution.