Schneider Electric ATSU01N209LT, EAN: 3389110667097

Schneider Electric ATSU01N209LT soft starter 9 A

Industrial Material > Automation > Frequency converter, soft starter

Schneider Electric ATSU01N209LT soft starter 9 A

Lieske Part No. 550604
Mfg Part No ATSU01N209LT
EAN-Code 3389110667097
Manufacturer Schneider Electric
Here only 294,50 EUR
350,46 EUR incl. VAT

Further information for Schneider Electric ATSU01N209LT soft starter 9 A

Complementary
Assembly styleWith heat sink
Function availableIntegrated bypass
Supply voltage limits180…528 V
Supply frequency50...60 Hz - 5...5 %
Network frequency47.5...63 Hz
[Uc] Control circuit voltage24 V DC +/- 10 %
Starting time1 s / 100; 5 s / 20; 10 s / 10; Adjustable from 1 to 10 s
Deceleration time symbAdjustable from 1 to 10 s
Starting torque30...80 % of starting torque of motor connected directly on the line supply
Discrete input typeLogic (LI1, LI2, BOOST) stop, run and boost on start-up functions
Discrete input voltage24...40 V
Input output isolationGalvanic between power and control
Discrete input logicPositive LI1, LI2, BOOST at State 0: < 5 V and 13 V, >= 0.5 mA
Discrete output current2 A DC-13; 3 A AC-15
Discrete output typeOpen collector logic LO1 end of starting signal; Relay outputs R1A, R1C NO
Discrete output voltage24 V (voltage limits: 6...30 V) open collector logic
Minimum switching current10 mA at 6 V DC for relay outputs
Maximum switching currentRelay outputs: 2 A at 30 V DC cos phi = 0.5 and L/R = 20 ms inductive load; Relay outputs: 2 A at 250 V AC AC-15 cos phi = 0.5 and L/R = 20 ms inductive load
Maximum switching voltage440 V relay outputs
Display type1 LED (green) for starter powered up; 1 LED (yellow) for nominal voltage reached
Tightening torque0.5 N.m; 1.9…2.5 N.m
MarkingCE
Operating positionVertical +/- 10 degree
Height234 mm
Width45 mm
Depth150 mm
Net weight0.34 kg
Power range1.1…2 kW at 200…240 V 3 phases; 2.2…3 kW at 380…440 V 3 phases; 4…6 kW
Motor starter typeSoft starter
Contractual warranty
Warranty (in months)18
Environment
StandardsEN/IEC 60947-4-2
Product certificationsUL; C-Tick; CSA; CCC
IP degree of protectionIP20
Pollution degree2 conforming to EN/IEC 60947-4-2
Vibration resistance1 gn (f= 13…150 Hz) conforming to EN/IEC 60068-2-6; 1.5 mm peak to peak (f= 3…13 Hz) conforming to EN/IEC 60068-2-6
Shock resistance15 gn for 11 ms conforming to EN/IEC 60068-2-27
Relative humidity5…95 % without condensation or dripping water conforming to EN/IEC 60068-2-3
Ambient air temperature for operation-10…40 °C (without derating); 40…50 °C (with current derating of 2 % per °C)
Ambient air temperature for storage-25…70 °C conforming to EN/IEC 60947-4-2
Operating altitude1000 m with current derating of 2.2 % per additional 100 m
Logistical informations
Country of originDE
Main
Range of productAltistart U01 and TeSys U
Product destinationAsynchronous motors
Product or component typeSoft starter
Product specific applicationSimple machine
Device short nameATSU01
Network number of phases3 phases
[Us] rated supply voltage200...480 V - 10...10 %
Motor power kW4 kW, 3 phases at 400 V; 1.5 kW, 3 phases at 230 V
Motor power hp2 hp, 3 phases at 230 V; 5 hp, 3 phases at 460 V
IcL starter rating9 A
Utilisation categoryAC-53B conforming to EN/IEC 60947-4-2
Current consumption65 mA
Type of startStart with voltage ramp
Power dissipation in W1.5 W at full load and at end of starting; 91.5 W in transient state
Packing Units
Unit Type of Package 1PCE
Number of Units in Package 11
Package 1 Height6.500 cm
Package 1 Width18.500 cm
Package 1 Length16.500 cm
Package 1 Weight454.000 g
Unit Type of Package 2S03
Number of Units in Package 214
Package 2 Height30 cm
Package 2 Width30 cm
Package 2 Length40 cm
Package 2 Weight6.905 kg
The Altistart U01 is a soft start/soft stop device for 3-phase asynchronous motors. It is primarily intended to be combined with TeSys U-Starter controllers. It can be used for a motor with a rated power of up to 4 kW or 5 HP for 3 phases (200 V to 480 V AC) and up to 9 A. With a width of 45 mm, it is one of the smallest soft starters on the market. It can be installed almost anywhere. It has an integrated bypass that reduces noise and heat dissipation. The protection class is IP20. It weighs 0.34 kg and has the following dimensions: 45 mm wide, 234 mm high, 150 mm deep. The Altistart U01 is designed for the following simple applications: conveyor belts, pumps, fans, compressors, automatic doors and gates, small cranes and belt-driven machines. It complies with the IEC/EN 60947-4-2 standards and carries the UL, CSA, C-Tick and CCC certifications and the CE marking. It can be easily combined with a TeSys U controller using the VW3G4104 power connector. It is easy to install on a DIN rail. Altistart 01 combines simplicity with easy wiring, quick configuration and efficiency. Reduced machine wear and minimized maintenance times optimize operations. Together with the TeSys Model U, it offers a unique motor starter solution.
This is an offer of:

Lieske Elektronik e.K.

Reutener Str. 10
79279 Vörstetten

https://industry-electronics.com
Tel. 07666/88499-0
Fax. 07666/88499-111

Diesen Artikel finden Sie unter:
industry-electronics.com/artikel/550604
qrcode für Schneider Electric ATSU01N209LT soft starter 9 A