Complementary
Device connection	In line
Overload current	400 % Ie for 13 s
On-load factor	50 %
Operating cycles/hour	10 cyc/h
[Us] control circuit voltage	110...230 V AC 50...60 Hz - 15...10 %
Apparent power	70 VA
Integrated motor overload protection	True
motor thermal protection class	Class 10E
Protection type	Phase failure: mains; Thermal protection: mains; Thermal protection: starter; Current overload: motor; Motor underload: motor; Excessive acceleration time: motor; Motor phase loss detection: motor; Protection against line phase inversion: mains; External thermal protection: motor; Short-circuit between motor phase and earth: motor
current limiting %In (5 x Ie maximum)	150…700 %
Rated current pwr loss specification	170 A
Power loss static current independent	19 W
Power loss per device current dependent	28 W
Power loss during starting	1388 W during starting at 40 °C at 400% In
Standards	EN/IEC 60947-4-2; UL 60947-4-2; IEC 60664-1
Product certifications	cULus; CE; UKCA; CCC; RCM; EAC; KC
Marking	CULus; CE; UKCA; CCC; RCM; EAC; KC
[Uc] control circuit voltage	24 V DC
Discrete input number	4
Discrete input type	(STOP) digital input, 4.4 kOhm; (RUN) digital input, 4.4 kOhm; (DI3) digital input, 4.4 kOhm; (DI4) digital input, 4.4 kOhm
Input compatibility	STOP: digital input level 1 PLC conforming to EN/IEC 61131-2; RUN: digital input level 1 PLC conforming to EN/IEC 61131-2; DI3: digital input level 1 PLC conforming to EN/IEC 61131-2; DI4: digital input level 1 PLC conforming to EN/IEC 61131-2
Discrete input logic	Digital input STOP at State 0: 0...< 5 V and 11 V, >= 5 mA; Digital input RUN at State 0: 0...< 5 V and 11 V, >= 5 mA; Digital input DI3 at State 0: 0...< 5 V and 11 V, >= 5 mA; Digital input DI4 at State 0: 0...< 5 V and 11 V, >= 5 mA
Relay output number	2
Relay output type	Relay outputs R1A, R1C NO; Relay outputs R1B, R1C NC; Relay outputs R2A, R2C NO
Minimum switching current	100 mA at 12 V DC for relay outputs
Maximum switching current	Relay outputs 2 A / 250 V AC for AC-15 100000 cycles following IEC 60947-5-1; Relay outputs 2 A / 30 V DC for DC-13 150000 cycles following IEC 60947-5-1
Analogue input number	1
Analogue input type	PTC1 : PTC temperature probe; PTC2 : PTC temperature probe
Analogue output number	1
Analogue output type	Current output AQ1 : 0...20 mA/4...20 mA , impedance< 500 Ohm; Voltage output AQ1 : 0...10 V , impedance> 470 Ohm
Connector type	1 RJ45; Open style
Physical interface	2-wire RS 485 - connector(s): RJ45; 2-wire RS 485 - connector(s): open style (DO, D1, PE, COM)
Transmission frame	RTU : 1 RJ45; RTU : open style (DO, D1, PE, COM)
Transmission rate	4.8…38.4 kbps for Modbus serial RJ45; 0.3...115.2 kbps for Modbus serial open style (DO, D1, PE, COM)
Data format	8 bits, odd, even or no parity, 1 or 2 bits to stop for Modbus serial RJ45; 8 bits, configurable odd, even or no parity for Modbus serial open style (DO, D1, PE, COM)
Number of addresses	0…247 for Modbus serial
Method of access	Slave Modbus serial
Type of polarization	No impedance for Modbus serial
Display screen available	True
Operating position	Vertical +/- 10 degree
Height	356 mm
Width	160 mm
Depth	231.5 mm
Net weight	8.60 kg
internal bypass	True
Function available	Single direction; Pre-heating; Power monitoring; Condition monitoring; User management; Ports and services hardening; Security event logging; Cybersecure firmware update; Small motor test
material declaration	True
Contractual warranty
Warranty (in months)	18
Environment
Electromagnetic compatibility	Conducted and radiated emissions level A conforming to IEC 60947-4-2; Electrostatic discharge level 3 conforming to IEC 61000-4-2; Immunity to radiated radio-electrical interference level 3 conforming to IEC 61000-4-3; Immunity to electrical transients level 4 conforming to IEC 61000-4-4; Voltage/current impulse level 3 conforming to IEC 61000-4-5; Damped oscillating waves level 3 conforming to IEC 61000-4-18; Immunity to conducted disturbances radio-frequency level 3 conforming to IEC 61000-4-6
Pollution degree	Level 3
[Uimp] rated impulse withstand voltage	6 kV
[Ui] rated insulation voltage	600 V
Environmental class (during operation)	Class 3C3 according to IEC 60721-3-3; Class 3S3 according to IEC 60721-3-3
Ambient air temperature for operation	-25…40 °C (without derating); 40…60 °C (with current derating of 1 % per °C above 40 °C)
Ambient air temperature for storage	-40…70 °C
Ambient air transport temperature	-40…70 °C
Operating altitude	2000...4800 m with current derating 1 % per 100 m above 2000 m
Relative humidity	5…95 % without condensation or dripping water conforming to EN/IEC 60068-2-3
Maximum deflection under vibratory load (during operation)	1.5 mm at 2...13 Hz
Maximum deflection under vibratory load (during storage)	1.75 mm at 2...9 Hz
Maximum deflection under vibratory load (during transport)	1.75 mm at 2...9 Hz
Maximum acceleration under vibrational stress (during operation)	1 gn at 13…200 Hz
Maximum acceleration under vibratory load (during storage)	1 gn at 9…200 Hz; 1.5 gn at 200…500 Hz
Maximum acceleration under vibratory load (during transport)	1 gn at 9…200 Hz; 1.5 gn at 200…500 Hz
Maximum acceleration under shock impact (during operation)	15 gn at 11 ms
Maximum acceleration under shock load (during storage)	10 gn at 11 ms
Maximum acceleration under shock load (during transport)	10 gn at 11 ms
Logistical informations
Country of origin	ID
Main
Range of product	Altivar Soft Starter ATS430
Product or component type	Soft starter
Product destination	Asynchronous motors
Product specific application	Standard industrial machines
Device short name	ATS430
Network number of phases	3 phases
Utilisation category	AC-3A; AC-53A
Ue power supply voltage	208...600 V AC (- 15...10 %)
power supply frequency	50...60 Hz - 20...20 %
[Ie] rated operational current	Normal duty: 170 A in line (at
Service factor at Ie	100
Torque control	True
IP degree of protection	IP00
Motor power kW	45 kW at 230 V in line normal duty; 90 kW at 400 V in line normal duty; 90 kW at 440 V in line normal duty; 110 kW at 500 V in line normal duty; 110 kW at 525 V in line normal duty
Motor power hp	50 hp at 208 V normal duty; 60 hp at 230 V normal duty; 125 hp at 460 V normal duty; 150 hp at 575 V normal duty
Communication port protocol	Modbus serial
Packing Units
Unit Type of Package 1	PCE
Number of Units in Package 1	1
Package 1 Height	22.500 cm
Package 1 Width	27.500 cm
Package 1 Length	45.000 cm
Package 1 Weight	10.592 kg
Unit Type of Package 2	S06
Number of Units in Package 2	6
Package 2 Height	75.000 cm
Package 2 Width	60.000 cm
Package 2 Length	80.000 cm
Package 2 Weight	72.000 kg

Der ATS430 ist dazu bestimmt, Asynchronmotoren, von 208 bis 600V, sanft zu starten und zu stoppen. Mit einem Wirkungsgrad von 99,5% und speziellen Anwendungsfunktionen ermöglicht der ATS430 eine fortschrittliche Motorsteuerung. Best Practices der Cybersicherheit und Zustandsüberwachung erhöhen die Betriebszeit, senken die Betriebskosten und vereinfachen die Projektplanung. Der ATS430 ermöglicht eine Messung der Leistung und der Energie, mit einer Genauigkeit von über 95%. Der Altivar Sanftanlasser ATS430 erfüllt die Anforderungen von Anwendungen wie Pumpen, Ventilatoren, Kompressoren, Förderbändern, Mischern, Schneidemaschinen, Schleifmaschinen und Brechern. Entspricht IEC/EN 60947-4-2 und den Zertifizierungen CE, cULus, UKCA, RCM, CCC, EAC. Es sind viele Zubehörteile verfügbar, wie ein IP65-Montagesatz zur Befestigung des Grafik-Displays an der Schaltschranktür und Kommunikationsmodule zur Erweiterung der Konnektivität auf andere Protokolle. Die Verpackung besteht aus recyceltem Karton und enthält weniger Einwegplastik. Die ATS430-Sanftanlasser müssen vertikal in einem Gehäuse montiert werden. Die eingebauten und innovativen Funktionen des ATS430 verbessern die Wettbewerbsfähigkeit, die betriebliche Widerstandsfähigkeit und die Nachhaltigkeit der Ausrüstung.