Schneider Electric ATH230U06M2, EAN: 3606487957621

Schneider Electric ATH230U06M2 frequency converter 0.55 kW

Industrial Material > Automation > Frequency converter, soft starter

Schneider Electric ATH230U06M2 frequency converter 0.55 kW

Lieske Part No. 893920
Mfg Part No ATH230U06M2
EAN-Code 3606487957621
Manufacturer Schneider Electric
Here only 312,55 EUR
371,93 EUR incl. VAT

Further information for Schneider Electric ATH230U06M2 frequency converter 0.55 kW

Complementary
Apparent power1.6 kVA at 240 V
Power dissipation in W33 W
Discrete input number7
Discrete input typeSTO safe torque off, 24 V DC, impedance: 1.5 kOhm; DI1...DI6 logic inputs, 24 V DC (30 V); DI5 programmable as pulse input: 0…30 kHz, 24 V DC (30 V)
Discrete input logicPositive logic (source); Negative logic (sink)
Discrete output number1
Discrete output typeOpen collector DQ+ 0…1 kHz 30 V DC 100 mA; Open collector DQ- 0…1 kHz 30 V DC 100 mA
Analogue input number3
Analogue input typeAI1 voltage: 0...10 V DC, impedance: 30 kOhm, resolution 10 bits; AI2 bipolar differential voltage: +/- 10 V DC, impedance: 30 kOhm, resolution 10 bits; AI3 current: 0...20 mA (or 4-20 mA, x-20 mA, 20-x mA or other patterns by configuration), impedance: 250 Ohm, resolution 10 bits
Analogue output number1
Analogue output typeSoftware-configurable current AQ1: 0...20 mA impedance 800 Ohm, resolution 10 bits; Software-configurable voltage AQ1: 0...10 V DC impedance 470 Ohm, resolution 10 bits
Relay output number2
Relay output typeConfigurable relay logic R1A 1 NO electrical durability 100000 cycles; Configurable relay logic R1B 1 NC electrical durability 100000 cycles; Configurable relay logic R1C; Configurable relay logic R2A 1 NO electrical durability 100000 cycles; Configurable relay logic R2C
Maximum switching currentRelay output R1A, R1B, R1C on resistive load, cos phi = 1: 3 A at 250 V AC; Relay output R1A, R1B, R1C on resistive load, cos phi = 1: 3 A at 30 V DC; Relay output R1A, R1B, R1C, R2A, R2C on inductive load, cos phi = 0.4 and L/R = 7 ms: 2 A at 250 V AC; Relay output R1A, R1B, R1C, R2A, R2C on inductive load, cos phi = 0.4 and L/R = 7 ms: 2 A at 30 V DC; Relay output R2A, R2C on resistive load, cos phi = 1: 5 A at 250 V AC; Relay output R2A, R2C on resistive load, cos phi = 1: 5 A at 30 V DC
Minimum switching currentRelay output R1A, R1B, R1C, R2A, R2C: 5 mA at 24 V DC
Physical interface2-wire RS 485
Connector typeRJ45
Method of accessServer Modbus serial; Subordinate BACnet MS/TP
Transmission rate4800 bps, 9600 bps, 19200 bps, 38.4 Kbps; 9.6, 19.2, 38.4, 76.8 kbit/s
Transmission frameRTU; MS/TP
Number of addresses0…247; 0…127
Data format8 bits, configurable odd, even or no parity 1or 2 stop
Type of polarizationNo impedance
Line current7.8 A at 200 V; 6.6 A at 240 V
Prospective line Isc1 kA
Output frequency0.599 kHz
Switching frequency2...16 kHz adjustable; 4...16 kHz with derating
nominal switching frequency4 kHz
4 quadrant operation possibleTrue
Asynchronous motor control profileVoltage/frequency ratio, 5 points; Flux vector control with sensor, standard; Voltage/frequency ratio - Energy Saving, quadratic U/f; Flux vector control without sensor - Energy Saving; Voltage/frequency ratio, 2 points
Synchronous motor control profileVector control without sensor
Acceleration and deceleration rampsLinear; U; S; CUS; Ramp switching; Acceleration/deceleration ramp adaptation; Acceleration/deceleration automatic stop with DC injection
Motor slip compensationAutomatic whatever the load; Adjustable 0...300 %; Not available in voltage/frequency ratio (2 or 5 points)
Braking to standstillBy DC injection
Brake chopper integratedTrue
StandardsIEC 61800-5-1; IEC 61800-3; UL 508C; IEC 61800-3 environments 1 category C2; IEC 61800-3 environments 2 category C3; IEC 60721-3; IEC 61508; IEC 13849-1
Product certificationsCULus; CE; UKCA; KC; EAC; ATEX; RCM
MarkingCULus; CE; UKCA; KC; EAC; ATEX; RCM
With safety function Safe torque off (STO)True
Protection typeLine supply phase loss: drive; Motor phase loss: motor; Line supply overvoltage and undervoltage: drive; Overheating protection: drive; Overload: motor; With PTC probes: motor; Short-circuit between motor phases: drive; Overcurrent between output phases and earth: drive
Width72 mm
Height143 mm
Depth143 mm
Net weight1.1 kg
Function availableFire mode; Run permissive; PID controller; Additional PID; Damper control; Underload detection for broken belt
Contractual warranty
Warranty (in months)18
Environment
Pollution degree2
Operating positionVertical +/- 10 degree
Electromagnetic compatibilityElectrostatic discharge immunity test level 3 conforming to IEC 61000-4-2; Radiated radio-frequency electromagnetic field immunity test level 3 conforming to IEC 61000-4-3; Electrical fast transient/burst immunity test level 4 conforming to IEC 61000-4-4; 1.2/50 µs - 8/20 µs surge immunity test level 3 conforming to IEC 61000-4-5; Conducted radio-frequency immunity test level 3 conforming to IEC 61000-4-6; Voltage dips and interruptions immunity test conforming to IEC 61000-4-11
Environmental class (during operation)Class 3C3 according to IEC 60721-3-3; Class 3S2 according to IEC 60721-3-3
Maximum acceleration under shock impact (during operation)150 m/s² at 11 ms
Maximum acceleration under vibrational stress (during operation)10 m/s² at 13...200 Hz
Relative humidity5…95 % without condensation or dripping water conforming to EN/IEC 60068-2-3
Overvoltage categoryIII
Ambient air transport temperature-25…70 °C
Ambient air temperature for operation-10…50 °C without derating; 50…60 °C with derating factor
Ambient air temperature for storage-25…70 °C
Logistical informations
Country of originID
Main
Range of productAltivar HVAC ATH200
Product specific applicationHVAC
Product or component typeVariable speed drive
VariantStandard version
Device short nameATH230
Product destinationAsynchronous motors; Synchronous motors
Mounting modeCabinet mount
IP degree of protectionIP20
Network number of phases1 phase
[Us] rated supply voltage200...240 V - 15...10 %
Relative symmetric mains voltage tolerance10 %
Supply frequency50...60 Hz - 5...5 %
Relative symmetric network frequency tolerance5 %
nominal output current3.7 A
Maximum transient current4.1 A
Motor power kW0.55 kW
Motor power hp0.75 hp
Safety functionSTO (safe torque off)
Safety levelSIL 3 conforming to IEC 61508; PL = e conforming to ISO 13849-1
EMC filterClass C2 EMC filter integrated
Communication port protocolModbus serial; BACnet MS/TP
Option cardCommunication module for BACnet IP
Packing Units
Unit Type of Package 1PCE
Number of Units in Package 11
Package 1 Height11.500 cm
Package 1 Width18.700 cm
Package 1 Length19.000 cm
Package 1 Weight1.339 kg
Unit Type of Package 2P06
Number of Units in Package 245
Package 2 Height75.000 cm
Package 2 Width60.000 cm
Package 2 Length80.000 cm
Package 2 Weight73.255 kg
Die Altivar HVAC ATH200-Reihe umfasst Frequenzumrichter, die für Erstausrüster (OEMs) im Bereich Heizungs-, Lüftungs- und Klimatechnik (HLK) zur Versorgung von Asynchron- und Synchronmotoren entwickelt wurden. Mit der Schutzart IP20 eignet sich der ATH230 für die Montage in Schaltschränken. Er versorgt 0.55kW / 0.75PS Motoren bei einer Nennspannung von 200 bis 240 V. Das robuste Design mit beschichteten Leiterplatten der Klasse 3C3 gemäß IEC 60721-3-3 erhöht die Maschinenverfügbarkeit unter rauen Umgebungsbedingungen. Umgebungstemperaturen von bis zu 60 °C, ohne zusätzliche Kühlung. Sein kompaktes Design und native Funktionen wie Safe Torque Off, EMV-Filter und A2L-Zertifizierung optimieren das Bedienfeld und steigern die Wettbewerbsfähigkeit. HVAC- und programmierbare Logikfunktionen sind integriert, um das Automatisierungssystem zu vereinfachen. ATH200 verfügt über native Modbus-, BACnet MS/TP-Seriellschnittstellen und BACnet/IP-Konnektivität mit einem optionalen Kommunikationsmodul. Die Abmessungen betragen 72mm (Breite), 143mm (Tiefe), 143mm (Höhe) und er wiegt 1.1kg. ATH230 verwendet Kunststoff mit einem biobasierten Anteil von mehr als 20 % und Aluminium ist ASI-zertifiziert. Altivar HVAC ATH200 erfüllt die Anforderungen kompakter HLK-Anlagen, die Pumpen-, Lüfter- und Kompressoranwendungen abdecken. Es entspricht den Normen IEC/EN 81800-5-1 und IEC/EN 61800-3 und verfügt über die Zertifizierungen CE, cULus, UKCA, RCM, EAC, KC und ATEX. Für Altivar HVAC ATH200-Frequenzumrichter sind Montagezubehör und externe Optionen wie Netzdrosseln, Motordrosseln und zusätzliche EMV-Filter erhältlich. Die Verpackung besteht aus recyceltem Karton und enthält kein Einwegplastik. Es ist für die vertikale Montage (+/- 10 °) auf einer Platte mit 4 Befestigungslöchern ausgelegt. Die integrierten Funktionen und das ATH200-Design verbinden die Wettbewerbsfähigkeit kompakter HLK-Geräte mit Zuverlässigkeit, Effizienz und ökologischer Nachhaltigkeit. ATH230 bietet kompakte Lösungen ohne Kompromisse beim thermischen Verhalten, um das Design des HLK-Bedienfelds zu optimieren und gleichzeitig hohe Effizienz und Zuverlässigkeit zu gewährleisten.
This is an offer of:

Lieske Elektronik e.K.

Reutener Str. 10
79279 Vörstetten

https://industry-electronics.com
Tel. 07666/88499-0
Fax. 07666/88499-111

Diesen Artikel finden Sie unter:
industry-electronics.com/artikel/893920
qrcode für Schneider Electric ATH230U06M2 frequency converter 0.55 kW