Two 30W ports, extends PoE range by 100m, 60W PoE power budget, IEEE 802.3bt compliant (4PPoE), IP67 waterproof, IK10 vandal resistant, metal case
Gigabit PoE++ Extender - 60W with IEEE 802.3bt (4PPoE) for Demanding outdoor use:
The Gigabit PoE++ extender with vandalism protection for outdoor use from Intellinet Network Solutions extends the range of a PoE source device to up to two PoE end devices. Additional power supply is not required on the route but is obtained directly via the PoE input.
Robust design for outdoor use and industrial areas:
This 4PPoE extender is suitable for many environmental areas. Its weatherproof housing with IP67 protection is dust and waterproof. It also allows operation in extreme ambient temperatures from -40 to 80< and with an impact resistance level of IK10, it protects against vandalism. The additional levels of shock resistance (IEC 60068-2-27), free fall (IEC 60068-2-32) and vibration (IEC 60068-2-6) round off the robustness.
Less cabling costs:
As mentioned at the beginning: You don't need separate power lines to supply your PD equipment (powered devices). Simply connect the extender to your PoE switch or injector. According to the IEEE 802.3bt protocol, it absorbs up to 95 W of power over four pairs of wires and distributes it up to 30 W per output port (60 W total) and speeds of 10/100/1000 Mbit/s up to 200 m.
Safe protection for your expensive network equipment:
The autosensing technology of this Ultra PoE extender offers safe protection against short circuits, overcharging and overvoltage. There is also port overvoltage protection up to 6 kV.
Optional wall mounting:
For maximum flexibility when installing indoors and outdoors, the extender can be attached to a wall using the four mounting holes on the back. The required mounting material is included in the scope of delivery.

• Doubles the maximum connection range between PoE source and device from 100 m to 200 m
• Power supply and network connection for two PoE devices such as network cameras, access points or VoIP phones from a PSE port through a PoE injector or PoE switch
• Delivers up to 60W to two connected PoE devices with up to 30W per port
• IP67 rating, waterproof and dustproof
• IK10 shock resistance rating, vandal-proof
• Supports 10/100/1000 Mbps data transfer rates
• PoE power budget 60 watts
• Saves Time and installation costs due to the transmission of data and power over the existing network cables
• Does not require additional power supply; draws power directly via the PoE input
• power is only transmitted to IEEE 802.3af/at-compliant devices, non-PoE-capable devices only receive data
• protection against overvoltage, overcharging and voltage spikes
• ground point for protection against external electrical voltage spikes
• port -Surge protection up to 6 kV
• Compatible with IEEE 802.3bt/at/af-compliant PoE injectors and switches (PSE)
• Compatible with all IEEE 802.3at/af-compliant Powered Devices (PD)
• Can be used as a 3-port Gigabit switch with PoE power supply and PoE passthrough
• 6 Gbit/s switch fabric
• Supports jumbo frames up to 9 kByte
• Supports 2048 MAC address entries
• Suitable for wall mounting
• Grounding kit included
• 3 year warranty Standards
• IEEE 802.3af (Power over Ethernet)
• IEEE 802.3at (High-Power PoE+ Power over Ethernet)
• IEEE 802.3bt (Ultra PoE++/4PPoE Power over Ethernet)
• IEEE 802.3i (10Base-T Ethernet)
• IEEE 802.3ab (Gigabit Ethernet)
• IEEE 802.3x (Full duplex and flow control)
• IEEE 802.3u (100Base-TX Fast Ethernet)
General

• Supported media:
• 10Base-T Cat5e UTP/STP RJ45, 8-pin.
• 100Base-TX Cat5e UTP/STP RJ45, 8-pin.
• 1000Base-T Cat5e UTP/STP RJ45, 8-pin.
• Ports:
• 1 x RJ45 10/100/1000 Mbit/s input
• 2 x RJ45 10/100/1000 Mbit/s PoE output port
• MAC address table: 2048 entries
• Cache: 256 kB
• Backplane speed: 6 Gbit/s
• Store-and-Forward Architecture
• Certificates: FCC Class A, CE, RoHS
PoE Pinout

• Pin 1: DC (+)
• Pin 2: DC (+)
• Pin 3: DC (-)
• Pin 6: DC (-)
Power

• Maximum PD output current: 30W per port, 44 - 55VDC
• Input current: IEEE 802.3bt/at/af compliant PSE, 95W max, 44 - 57VDC
Physical Details

• IEC- Rating: IP67 (weatherproof) and IK10 (vandal-proof metal housing)
• Dimensions: 150 x 73 x 44 mm
• Suitable network cable diameter: 5.5 mm max.
• Weight: 353 g
• Operating temperature: -20 - 60°C
• Storage temperature: -40 - 80°C (-40 - 176°F)
• Humidity during operation: 10 - 90% RH, non-condensing
• Storage humidity: 5 - 90% RH, non-condensing
Scope of delivery

• 2-port outdoor Gigabit PoE++ extender with vandalism protection
• Grounding kit
• Three cable glands with protection class IP67
• Quick guide Color: Silver Product dimensions: 114.6 (L) x 72.6 (W) x 38.3 (H) [mm]