Hager ADA510D, EAN: 3250611067740

Hager ADA510D RCD 1P+N 30mA

Installation > Modular devices / equipment installation > RCD

Hager ADA510D RCD 1P+N 30mA

Lieske Part No. 226293
Mfg Part No ADA510D
EAN-Code 3250611067740
Manufacturer Hager
Here only 157,22 EUR
187,09 EUR incl. VAT

Further information for Hager ADA510D RCD 1P+N 30mA

General
Number of poles (total)2
Number of protected poles1
Rated voltage240 V
Rated insulation voltage Ui500 V
Rated impulse withstand voltage Uimp4 kV
Rated current10 A
Rated fault current0.03 A
Leakage current typeA
Current limiting class3
Rated short-circuit breaking capacity IEC 60947-210 kA
Rated short-circuit breaking capacity Icn acc. EN 61009-110 kA
Disconnection characteristicUndelayed
Surge current capacity0.25 kA
Voltage typeAC
Frequency50 Hz
Release characteristicB
Over voltage category3
Pollution degree2
Ambient temperature during operating40 °C
Width in number of modular spacings2
Built-in depth68 mm
Degree of protection (IP)IP2X
Connectable conductor cross section solid-core25 mm²
Connectable conductor cross section multi-wired16 mm²
Power loss3.40 W
Concurrently switching N-neutralyes
With interlocking deviceyes
Anti-nuisance tripping versionno
The ADA510D residual current circuit breaker from Hager is a combined protection switch for use in electrical installations, providing protection against overcurrent as well as residual currents. It is designed as a 1P+N switch, with one pole protected and the neutral conductor switching simultaneously. The switch is rated for a nominal voltage of 240 V and a nominal current of 10 A, and provides residual current protection with a rated residual current of 30 mA. The tripping characteristic is type B, making it suitable for applications with typical consumers in residential and commercial buildings. The residual current type A enables detection of sinusoidal alternating and pulsating direct residual currents, which is particularly relevant for devices with electronic circuits.

Applications

The switch is designed for use in residential and commercial buildings where high safety standards for electrical supply are required. It is suitable for installations operating electronic devices, such as computer technology or LED lighting, as these often generate pulsating direct residual currents. The protection class IP2X ensures protection against contact with fingers and larger objects, but not against splashing water or dust. The operating temperature ranges up to 40 °C, and the switch can also be operated at temperatures as low as -25 °C, with the nominal current increasing accordingly.

Functions and Equipment in Detail

The ADA510D features a locking device that enables secure mounting and locking within an enclosure. The energy limitation class 3 ensures limited energy development in the event of a fault, enhancing safety. The switch is rated for a nominal breaking capacity of 10 kA, making it suitable for use in networks with high short-circuit currents. The impulse withstand capability is 0.25 kA, ensuring resilience against transient voltage surges. The connection cross-sections are designed for flexible conductors up to 16 mm² and rigid conductors up to 25 mm², enabling flexible integration into existing installations.

Technology Explained Simply

The switch combines the functions of a circuit breaker (LS) and a residual current switch (FI). In the event of an overcurrent, such as a short circuit, the thermal tripping device activates, based on heat generation from excessive current. In the case of a residual current, such as insulation defects, the electronic part of the switch detects the current difference between the incoming and outgoing lines and also trips. The type B tripping characteristic means the switch trips at a current of approximately 3 to 5 times the nominal current, which is suitable for typical consumers. The rated insulation voltage of 500 V and the rated impulse voltage withstand of 4 kV ensure high electrical strength.

Compatibility and Accessories

The switch is designed for mounting on a DIN rail and occupies two module widths. It is compatible with various accessories, including spacing elements for heat dissipation (LZ060), signal contacts (MZ202), auxiliary contacts (MZ201), cable bridges (K67G, K67M, K67E, K67F, K67L), and phase bar end caps (KZN023, KZN024). These components allow flexible adaptation to specific installation requirements, such as avoiding heat transfer or integrating signaling.

Mounting and Installation

Mounting is done on a DIN rail, with an installation depth of 68 mm. The connection terminals are designed for a nominal torque of 2.10 Nm, ensuring a secure connection. The device lifespan is 2000 mechanical and 2000 electrical switching operations, enabling high operational reliability over an extended period. The maximum altitude for use is 2000 m above sea level, with an operating temperature range between -25 °C and 40 °C.

Advantages in Operation

The switch provides reliable combined protection, enhancing both the safety of the installation and of personnel. The locking device and compact design facilitate mounting and maintenance. Compatibility with various accessories allows individual adaptation to specific requirements. The high breaking capacity of 10 kA and energy limitation class 3 ensure safe disconnection in case of faults, minimizing damage to the installation. The power loss is 3.40 W, indicating low energy consumption during operation.

Protection Class and Environmental Conditions

The protection class IP2X protects against contact with fingers and larger objects, but is not suitable for outdoor use or in damp environments. The pollution degree 2 corresponds to environments with low pollution, such as indoor spaces. The overvoltage category 3 is suitable for installations connected at the distribution level, such as in residential and commercial buildings. The storage and transport temperature ranges up to 70 °C, enabling safe storage under normal conditions.

Connection and Conductor Cross-Section

The switch can be connected with flexible conductors up to 16 mm² and rigid conductors up to 25 mm². The connection terminals are designed for a secure connection, with the nominal torque of 2.10 Nm to be maintained. The connection cross-sections are identical at both input and output, enabling flexible integration into existing installations. The maximum operating voltage is 240 V, and the frequency is fixed at 50 Hz.
This is an offer of:

Lieske Elektronik e.K.

Reutener Str. 10
79279 Vörstetten

https://industry-electronics.com
Tel. 07666/88499-0
Fax. 07666/88499-111

Diesen Artikel finden Sie unter:
industry-electronics.com/artikel/226293
qrcode für Hager ADA510D RCD 1P+N 30mA