Further information for Finder 222290244000 Relay 24 V DC 20 A Test Button
General
Degree of protection
IP 20
Operating voltage
24 V DC
Rated power
1,25 W
Coil resistance
460 Ohm
Contact material
AgSnO2
Number of contacts
2 Normally open contact (NO)
Max. continuous current
20 A
Nominal voltage
250 V AC
Max. switching capacity AC1
5000 VA
Max. switching capacity AC15
1000 VA
Incandescent and halogen lamps
1000 W
Fluorescent lamps with EVG
400 W
Fluorescent lamps with KVG
360 W
Energy-saving lamps
200 W
LED (230 V AC)
200 W
NV halogen lamps or LED with EVG
200 W
NV halogen lamps or LED with KVG
400 W
Response time
30 ms
Reset time
20 ms
Voltage strength coil/contacts
6 kV
Ambient temperature
-25…+50 °C
DIN rail
35 mm
Protection circuitry
Varistor (voltage-sensitive resistor)
Control
AC/DC ripple-free
Insulation
reinforced
Norm
EN 61095:2009-11
Flame retardancy
EN 45545-2 + A1:2016
Test button
The installation relay of Finder's series 22, type 22.22.9.024.4000, is a mounting device for installation on a 35 mm support rail, commonly used in electrical installations. It is designed for controlling electrical loads in installations, particularly in areas such as hotel room lighting, parking lot or street lighting, office and bathroom lighting control, as well as pump control applications. The device features two close contacts and is rated for a continuous current of 20 A at 250 V AC. The contact material consists of AgSnO₂, ensuring high switching durability for loads with high inrush currents, such as those occurring with lamp loads. The relay's protection rating is IP 20, providing protection against finger contact and solid foreign objects, but not against water or dust. The device is intended for indoor use.
Applications
This relay is suitable for applications in building and industrial automation where reliable and safe switching of electrical loads is required. It is particularly suitable for controlling lighting systems, including incandescent and halogen lamps, fluorescent lamps with electronic or conventional ballasts, energy-saving lamps, and LED lighting. The maximum switching capacity is 5000 VA (AC1) and 1000 VA (AC15) at 230 V AC, covering a wide range of loads. The switching capacity for incandescent and halogen lamps is 1000 W, for fluorescent lamps with electronic ballast (EVG) 400 W, with conventional ballast (KVG) 360 W, for energy-saving lamps 200 W, for LED lighting 200 W, and for NV halogen lamps or LED with EVG 200 W and with KVG 400 W.
Functions and Features in Detail
The relay includes a test button, allowing manual verification of the relay's function without having to switch off the control voltage. The coil is designed for an operating voltage of 24 V DC, with a rated power of 1.25 W and a resistance of 460 Ohm. The coil is designed for AC/DC actuation via internal circuitry, enabling noise-free operation. At the input, a protective circuit with a varistor is integrated to protect the coil against overvoltages. The mechanical life expectancy is 2 million switching cycles, and the electrical life expectancy under AC-7a operation is 70,000 switching cycles. The pickup and drop-out time is 30 ms and 20 ms, respectively.
Technology Explained Simply
The use of AgSnO₂ as contact material ensures high switching durability, especially for loads with high inrush currents, such as those occurring with lamps. The reinforced insulation between the coil and contacts increases safety and prevents unwanted electrical arcing. The protective circuit with a varistor protects the coil against transient voltage spikes caused by network disturbances or switching operations. The IP 20 protection rating means the device is protected against finger contact and the ingress of solid foreign objects, but not against water or dust.
Compatibility and Accessories
The relay is designed for mounting on a 35 mm support rail (EN 60715). It can be extended with a 6 A auxiliary switch, which can be mounted laterally on the device. As suitable accessories, the spacing piece 022.09 is offered, which serves for optical and mechanical alignment when mounting multiple devices on the rail.
Mounting and Installation
Mounting is performed on a standardized 35 mm support rail, commonly used in electrical installations. The width of the relay is 17.5 mm, enabling compact placement in enclosures. The test button facilitates commissioning and maintenance, as the relay's function can be checked without switching off the control voltage.
Operational Advantages
The relay offers high switching durability and reliability for controlling various types of loads. The noise-free actuation ensures quiet operation, and the integrated protective circuit increases the coil's lifespan. The combination of mechanical and electrical life expectancy, along with the IP 20 protection rating, makes the device suitable for a wide range of applications in building and industrial automation. The use of AgSnO₂ as contact material ensures long life under high inrush currents, particularly for lamp loads.
The device complies with standard EN 61095:2009-11 and is suitable for use in rail vehicles according to EN 45545-2 + A1:2016, concerning the fire behavior properties of materials and components. The ambient temperature range is -25 °C to +50 °C, enabling broad applicability in various environments.