DEHN 942110, EAN: 4013364495326

DEHN 942110 surge protector Type 2+3

DEHN 942110 surge protector Type 2+3

Lieske Part No. 602501
Mfg Part No 942110
EAN-Code 4013364495326
Manufacturer DEHN
Here only 201,21 EUR
239,44 EUR incl. VAT

Further information for DEHN 942110 surge protector Type 2+3

Technical data
Energy coordination with terminal equipment (≤ 10 m)type 2 + type 3
Nominal voltage (a.c.) (UN)230 V (50 / 60 Hz)
Max. continuous operating voltage (a.c.) [L-N] (UC)275 V (50 / 60 Hz)
Max. continuous operating voltage (a.c.) [N-PE] (UC)255 V (50 / 60 Hz)
Nominal discharge current (8/20 µs) (In)20 kA
Max. discharge current (8/20 µs) (Imax)40 kA
Combination wave [L-N] (UOC)20 kV
Combination wave [N-PE] (UOC)6 kV
Nominal load current for “V-connection” (IL)40 A
Voltage protection level [L-N]/[N-PE] (UP)≤ 1.5 / ≤ 1.5 kV
Voltage protection level [L-N]/[N-PE] at 5 kA (UP)≤ 1 / ≤ 1.5 kV
Protective conductor current (IPE)≤ 10 µA
Response time [L-N] (tA)≤ 25 ns
Response time [N-PE] (tA)≤ 100 ns
Max. mains-side overcurrent protection125 A gG
Max. mains-side overcurrent protection with “V-connection”40 A gG
Max. mains-side overcurrent protection with stub wiring (double connection 2 x 10 mm²)125 A gG
Short-circuit withstand capability for max. mains-side overcurrent protection (ISCCR)50 kArms
Temporary overvoltage (TOV) [L-N] (UT) – Characteristic335 V / 5 sec. – Festigkeit, 440 V / 120 min. – sicherer Ausfall
Temporary overvoltage (TOV) [N-PE] (UT) - Characteristic1200 V / 200 ms – withstand
Operating temperature range (TU)-40 °C ... +80 °C
Operating state / fault indicationgreen / red
Number of ports1
Cross-sectional area (min.)1,5 mm2 eindrähtig, 6 mm2 feindrähtig
Cross-sectional area (max.)10 mm2 solid / fine stranded
Cross-sectional area (min.) with wire end ferrule1.5 mm²
Cross-sectional area (max.) with wire end ferrule6 mm²
Cross-sectional area (max.) with wire end ferrule without collar10 mm²
For mounting on35 mm DIN rails acc. to EN 60715
Enclosure materialthermoplastic, red, UL 94 V-0
Place of installationindoor installation
Degree of protectionIP 20
Capacity2 Standard DIN module, DIN 43880
ApprovalsDEKRA, VDE
Mehrpoliger Überspannungsableiter DEHNguard MP, Typ 2 + Typ 3 nach EN 61643-11, bestehend aus Basisteil mit gesteckten Schutzmodulen und Doppel-Push-In-Anschlussklemme für Stich- und Durchgangsverdrahtung geeignet. Hohe Gerätesicherheit durch Ableiterüberwachung mit Thermo-Dynamik-Control. Zum Schutz von Niederspannungs-Verbraucheranlagen vor Überspannungen. Zum Einsatz im Blitz-Schutzzonen-Konzept an den Schnittstellen 0B - 1 und höher.
This is an offer of:

Lieske Elektronik e.K.

Reutener Str. 10
79279 Vörstetten

https://industry-electronics.com
Tel. 07666/88499-0
Fax. 07666/88499-111

Diesen Artikel finden Sie unter:
industry-electronics.com/artikel/602501
qrcode für DEHN 942110 surge protector Type 2+3