Allnet RP_SATA4xHv1.2, EAN: 4038816096593

Allnet RP_SATA4xHv1.2 SATA HAT board for Raspberry 4

Parts / kits > Robotics > electronic parts

Allnet RP_SATA4xHv1.2 SATA HAT board for Raspberry 4

Lieske Part No. 1787973
Mfg Part No RP_SATA4xHv1.2
EAN-Code 4038816096593
Manufacturer Allnet
Here only 48,97 EUR
58,27 EUR incl. VAT

Further information for Allnet RP_SATA4xHv1.2 SATA HAT board for Raspberry 4

General
Number of installable hard drives4
Hard disk formats2.5 inch, 3.5 inch
Current supply12V/5A
USB bus usageUSB3 buses of Raspberry Pi 4
SATA chipJMS561
Data transfer rate400 MB/s
Supported RAID modes0, 1, 5
Power supply for 3.5-inch hard drivesStandard ATX power supply (at least 60W)
Power supply for 2.5-inch hard drivesUSB PD/QC power supply (at least 30W)
UASP supportYes
HDD suspend modeYes
Optional OLED displayYes
Optional PWM fanYes
The product is a SATA Quad HAT NAS board for Raspberry Pi 4, manufactured by Allnet. It is an add-on board that converts a single-board computer such as the Raspberry Pi 4 into a network-attached storage (NAS) system. The board enables the connection of up to four hard drives or SSDs in 2.5 or 3.5 inch format, thereby providing a decentralized storage solution for small networks or home applications. The platform utilizes the USB3 buses of the Raspberry Pi 4 to double the connection capacity and enable higher data throughput performance.

Applications
The SATA Quad HAT is designed for use in private networks, small offices, or as a backup solution. It is particularly suitable for users who wish to provide an affordable and flexible networked storage space without relying on full server hardware. Support for software RAID modes such as RAID 0, 1, and 5 expands the application possibilities in terms of data security and performance. For 3.5-inch hard drives, an external ATX power supply is required, while 2.5-inch drives can be powered by a USB PD/QC power supply (minimum 30W).

Functions and Features in Detail
The board features two JMS561 chips, each supporting two SATA ports, allowing a total of four drives to be connected. Power supply is via a DC connector with 12V/5A. For 3.5-inch hard drive configurations, a standard ATX power supply is recommended, with a minimum output of 60W to power both the Raspberry Pi 4 and the hard drives. The board supports HDD suspend mode and UASP (USB Attached SCSI Protocol), which increases data transfer rates. Optionally, a PWM-controlled fan can be used for cooling the hard drives to optimize heat distribution. An OLED display is also optionally available to show IP address and storage information.

Technology Explained Simply
The SATA Quad HAT uses the USB3 interface of the Raspberry Pi 4 to expand connection options. The two JMS561 chips handle SATA control and enable read/write performance of up to 400 MB/s with four hard drives in RAID0 mode. Support for UASP improves data transfer efficiency, especially during large file transfers. Software RAID functions (RAID 0/1/5) allow flexible configuration of storage resources, with RAID 0 maximizing performance, RAID 1 enhancing data security, and RAID 5 offering a combination of both.

Compatibility and Accessories
The board is specifically designed for the Raspberry Pi 4 and requires its operating system for use. Compatible drives include 2.5- and 3.5-inch HDDs or SSDs. As accessories, a SATA NAS HAT Top Board is offered, providing additional features such as improved cooling or better cabling. A replacement power supply (12V/5A) is also available. For software control and monitoring, a Debian package is provided by Allnet.

Installation and Mounting
Mounting is done by stacking the HAT board onto the Raspberry Pi 4. Power supply must be provided through the DC connector on the SATA HAT to operate the system. Hard drives are connected via SATA ports. Software configuration is performed using the Debian package, which is installed via the operating system. Installation is not suitable for beginners, as knowledge of the Linux environment is required.

Advantages in Operation
The SATA Quad HAT offers an affordable way to convert a Raspberry Pi 4 into a powerful NAS system. Support for up to four hard drives and the ability to use software RAID modes increases the system’s flexibility and reliability. The high data throughput performance of up to 400 MB/s in RAID0 mode makes the board suitable for demanding applications. Optional cooling and the OLED display enhance operational safety and user-friendliness.
This is an offer of:

Lieske Elektronik e.K.

Reutener Str. 10
79279 Vörstetten

https://industry-electronics.com
Tel. 07666/88499-0
Fax. 07666/88499-111

Diesen Artikel finden Sie unter:
industry-electronics.com/artikel/1787973
qrcode für Allnet RP_SATA4xHv1.2 SATA HAT board for Raspberry 4