Allnet ALL126A Bundle, EAN: 4038816041265

Allnet ALL126A Bundle VDSL2 Set

Networks > VDSL

Allnet ALL126A Bundle VDSL2 Set

Lieske Part No. 898301
Mfg Part No ALL126A Bundle
EAN-Code 4038816041265
Manufacturer Allnet
Here only 299,76 EUR
356,71 EUR incl. VAT

Further information for Allnet ALL126A Bundle VDSL2 Set

General
Degree of protectionnot specified
Operation temperature0 °C
Storage temperature-20 °C
Air humidity10 %
Power consumption5,52 W
Operating voltage12 V
Amperage1 A
Ethernet ports4
Ethernet speed10/100 Mbps
VDSL2 standardITU-T G993.2
Bandwidth100 Mbit/s
Connection length2500 m
Band profiles8a, 8b, 8c, 8d, 12a, 12b, 17a, 17b, 30a
Frequency bands997, 998
Switching methodStore and forward
Console portRS-232C
Baud rate115200 bps
Current regulationIEEE 802.3x (Full duplex), Back pressure (Half duplex)
LED indicatorsPower, Link/Active (Ethernet), Link (VDSL2)
POTS/ISDN splitterIntegrated
Over voltage protectionIntegrated
ConfigurationWeb browser (HTTP), TFTP, RS232C console port
Downstream Power Back-Off (DPBO)supported
Loop back testsupported
Bridge modesupported
SNR indicationsupported
Interleave delaysupported
Wall mountingYes
Automatic speed adjustmentYes
The Allnet ALL126A Bundle is a VDSL2 modem pair, consisting of a master and a slave modem, designed for implementing permanent connections over existing 2-wire copper lines. The technology enables a maximum connection length of 2500 meters, with the achievable bandwidth depending on the length. At short distances, symmetric data rates up to 100 Mbit/s are possible. The solution is specifically suitable for use in facilities such as hotels or hospitals, where cost-effective and simple network equipment over existing telephone cabling is required. The modems operate according to the VDSL2 standard (ITU-T G993.2) and utilize the VDSL technology from Infineon to ensure reliable data transmission.

Applications
This modem pair is suitable for point-to-point connections as well as for connections to a DSL provider. It uses existing twisted two-wire telephone cables to establish a network connection without requiring additional cabling. The integrated function allows simultaneous use of the line for analog telephone calls, as an integrated PSTN splitter separates voice and data traffic. This makes the technology particularly valuable in environments where existing telephone infrastructure is already in place.

Functions and Equipment in Detail
Each modem features an integrated 4-port Ethernet switch with 10/100Mbps auto-negotiation, providing connectivity for network devices. The interfaces include one RJ-45 port for the VDSL2 connection and one RJ-11 connector for analog telephone or ISDN devices. The modems support various bandwidth profiles (8a, 8b, 8c, 8d, 12a, 12b, 17a, 17b, 30a) and bandwidth plans (997, 998), which can be configured according to requirements. The automatic speed setting for the VDSL2 port ensures optimal adaptation to line quality. Configuration is performed via a web browser or through the RS232C console port.

Technology Explained Simply
The modems use VDSL2 technology, which enables high data rates over short copper lines. The store-and-forward switching method ensures reliable data transmission within the local network. The integrated overvoltage protection function protects the devices from voltage surges. The diagnostic indicators (LEDs for Power, Ethernet Link/Active, VDSL2 Link) allow for quick status checks. Support for interleave delay helps reduce data errors and interference (noise). The Downstream Power Back-Off (DPBO) function optimizes downstream power supply to minimize power consumption.

Compatibility and Accessories
The bundle consists of the ALL126AM3 (master) and the ALL126AS3 (slave) or alternatively the ALL-BM100VDSL2, depending on stock availability. The modems are designed for use with twisted copper lines and support simultaneous use for telephony and data transmission. Configuration is performed via web interface (HTTP), TFTP, or RS232 console port. The modems are designed for operation in a temperature range of 0°C to 50°C and can be wall-mounted.

Installation and Mounting
The modems are compact (183 x 36 x 145 mm) and can be wall-mounted. Installation is carried out via the existing telephone line, using the RJ-11 connectors for telephone connection and the RJ-45 ports for network connection. Power supply is provided via an external power adapter (12V/1A). Configuration is performed via the web interface or the RS232C port.

Operational Advantages
The solution is characterized by low power consumption (5.52W to 6.12W) and energy-efficient operation. Integrated functions such as DSL splitter, overvoltage protection, and automatic speed setting reduce maintenance effort. Utilizing existing telephone lines minimizes installation costs and time. The modems are designed for use in commercial environments such as hotels or hospitals, where a reliable and cost-efficient network solution is required.

Scope of Delivery
The bundle includes one master modem (ALL126AM3) and one slave modem (ALL126AS3 or ALL-BM100VDSL2), one external power supply unit (12V/1A) each, one CD with manual (English) each, one LAN patch cable each, and one telephone patch cable (Western plug) each.
This is an offer of:

Lieske Elektronik e.K.

Reutener Str. 10
79279 Vörstetten

https://industry-electronics.com
Tel. 07666/88499-0
Fax. 07666/88499-111

Diesen Artikel finden Sie unter:
industry-electronics.com/artikel/898301
qrcode für Allnet ALL126A Bundle VDSL2 Set